Genie 7055 Program to Car: Expert Guide to HomeLink and Car2U Setup

Integrating your Genie garage door opener with your car’s built-in remote system enhances convenience and security. If you’re looking to program your Genie 7055 or similar model to your vehicle’s HomeLink or Car2U system, this expert guide provides step-by-step instructions. As automotive repair specialists at cardiagnostictool.store, we understand the importance of seamless vehicle integration. This article will walk you through the programming process, ensuring a smooth setup for both HomeLink and Car2U, eliminating the need for a separate handheld remote.

Programming Your Genie Garage Door Opener to HomeLink

HomeLink is a widely used in-car system that allows you to control various home automation devices, including Genie garage door openers. Typically found on your car’s visor or overhead console, HomeLink systems simplify your daily routine. Here’s how to program your Genie opener to a HomeLink system.

Step 1: Clear Existing HomeLink Programming

Before programming a new device, it’s recommended to clear any previous settings. To clear HomeLink:

1. Press and hold the first and third buttons on your HomeLink system simultaneously.
2. Keep holding until the HomeLink indicator light blinks slowly and then rapidly. This process usually takes about 20 seconds.
3. Release both buttons once the indicator blinks rapidly.

Note: Clearing HomeLink will erase all previously programmed devices.

Step 2: Synchronize HomeLink with Your Genie Remote Control

This step involves teaching your car’s HomeLink system to recognize the signal from your Genie remote.

1. Select the HomeLink button you wish to use for your Genie garage door opener.
2. Position your Genie remote approximately two inches away from the chosen HomeLink button.
3. Press and hold the button on your Genie remote that you typically use to open your garage door.
4. While still holding the Genie remote button, press and hold the selected HomeLink button at the same time.
5. Continue holding both buttons until the HomeLink indicator light changes from a slow blink to a rapid blink.
6. Once the rapid blinking begins, release both buttons.

Step 3: Finalize Programming with the Genie Opener Unit

The final step involves syncing HomeLink with your Genie garage door opener’s motor unit. The process varies slightly depending on whether you have a newer or older Genie model.

For Newer Genie Garage Door Openers (with a Program Button):

1. Locate the PROGRAM button on your Genie garage door opener powerhead. This is usually on the back of the unit.
2. Press and hold the PROGRAM button until the round blue LED illuminates. Then, release the button. The long purple LED will start flashing, indicating it’s in programming mode.
3. Inside your car, press and hold the HomeLink button you programmed in Step 2 for two seconds, then release. Repeat this press and release sequence a second time.
4. Observe the long LED on the opener unit. It should flash blue and then turn off, confirming signal reception.
5. Press the programmed HomeLink button several more times until your garage door begins to move. This might take a few attempts to fully synchronize.

For Older Genie Garage Door Openers (with a Learn Button):

1. Find the learn code button on your Genie garage door opener powerhead. The location varies, but it’s often on the back or side panel.
2. Press and release the learn code button. A red LED will begin to blink, indicating the unit is ready to learn.
3. Press the HomeLink button in your car one time. The red LED on the opener should stop blinking and remain on.
4. Press the same HomeLink button a second time. The red LED will turn off.
5. Press the HomeLink button again. Your garage door should now activate.

For more detailed instructions or troubleshooting, refer to your vehicle’s owner’s manual, HomeLink’s official website, or the Genie Company website.

Programming Your Genie Garage Door Opener to Car2U

Car2U is another in-car system similar to HomeLink, offering garage door control and other functionalities. While Car2U systems are pre-programmed for certain brands, they can also be configured to work with Genie garage door openers. Here’s how to set up Car2U with your Genie opener.

Car2U buttons for opening a garage door

Step 1: Reset Car2U to Factory Defaults

To ensure a clean programming process, it’s best to reset Car2U to its default settings. Car2U’s default button assignments are:

• Button 1 = Genie® Openers
• Button 2 = LiftMaster® Openers
• Button 3 = Wayne Dalton® Openers

To reset:

1. Press and hold buttons 1 and 3 on your Car2U system simultaneously for approximately 20 seconds.
2. Hold until all three LED lights above the Car2U buttons begin to flash.
3. Release both buttons. Car2U is now reset to factory default settings.

Note: Resetting Car2U will erase all previously programmed garage door openers.

Step 2: Program Car2U to Recognize Your Genie Opener

This step is similar to training HomeLink, but with the Car2U system.

For Newer Genie Models (with a Program Button):

1. Press and hold the PROGRAM button on your Genie garage door opener powerhead until the round blue LED turns on. Release the button. The long purple LED will begin to flash.
2. Press and hold the Car2U button you wish to program for your Genie opener for two seconds and release. Repeat this press and release sequence once more.
3. The long LED on the Genie opener should flash blue and then turn off.
4. Press the programmed Car2U button a few more times to test if the garage door activates.

For Older Genie Models (with a Learn Button):

1. Locate the learn code button on your Genie garage door opener powerhead.
2. Press and release the learn code button. The red LED will start to blink.
3. Press the desired Car2U button one time. The red LED should stop blinking and stay illuminated.
4. Press the same Car2U button once more. The red LED will turn off.
5. Press the Car2U button again to check if your garage door operates.

Step 3: Reassigning a Car2U Button for Genie Opener

If you wish to change the default assignment of Car2U buttons, especially to assign a different button to your Genie opener:

1. Press and hold buttons 1 and 3 on the Car2U system for ONE SECOND and release. All three LEDs will light up solid red.
2. Press and hold the button you want to reassign to Genie (button 2 or 3). The corresponding LED will flash. While holding this button, press and release button 1, then press and release button 1 again.
3. Release the button you held in step 2 and wait for the LED to stop flashing. This button is now configured for your Genie opener. Repeat for another Genie opener if needed.

For further assistance, consult your vehicle’s manual, learcar2u.com, or the Genie Company website.

By following these steps, you can easily program your Genie 7055 garage door opener to your car’s HomeLink or Car2U system. This integration provides a convenient and secure way to access your garage, enhancing your overall driving experience. For more automotive tech tips and diagnostic tool information, visit cardiagnostictool.store.